Проблемы с Syslog и MGCAMD_LOG_server
#1
Отправлено 27 December 2012 - 00:55
#2
Отправлено 27 December 2012 - 23:26
Сообщение отредактировал metpas: 27 December 2012 - 23:29
#4
Отправлено 09 January 2013 - 21:12
никак не получается установить прогу для лога пишет не обнаружено усттройство.все проверял уже неск раз тупик.а проблема в чем при попадании кодированного канала ресивер не переключается на другой ранее открывавшейся.приходиться из розетки дергать. помиге плизвсе настройки у нас есть,флуд надоел
на неделю в читатели
#6
Отправлено 09 January 2013 - 21:22
#7
Отправлено 09 January 2013 - 21:28
настройки в прогеоборудование какое?
в подпись внесите
[SETUP]
# Порт на компьютере по приему лога от MGCAMD
PORT=514
# Имя файла, в который будет записываться принимаемый лог
LOG_FILE="mgcamd.log"
# Файл mgshare.info (Если не задан - будет открыт ...\tmp\mgshare.info)
MGSHARE_INFO=""
# Файл replace.list
REPLACE_FILE=\\192.168.0.101\Configuration\keys\replace.list
# Информация о последней удачной загрузке (создается автоматически)
REPLACE_GOOD=\\BM750\Configuration\keys\replace.list
# Текстовый редактор (по умолчанию Notepad.exe)
EDITOR="Notepad.exe"
POISK=failed
#8
Отправлено 09 January 2013 - 21:30
# EMM messagesоборудование какое?
в подпись внесите
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 00 }
# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }
# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 01 }
# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
U: { 00 }
# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }
# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
G: { 01 }
# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 2 0
# network ecm timeout in seconds
K: { 03 }
# newcamd dead routes connect retry, sec
Q: { 07 }
# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 02 }
# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password
# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80
# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 01 } 192.168.0.100 514 /tmp/mgcamd.log
# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 20 }
# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E:) time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }
# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }
# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }
# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 12 }
# map all 180x nagra caids to 1801
# default is 01
F: { 00 }
CWS = 188.72.230.240 3001 6mfrlmc6 пароль 0102030405060708091011121314 # HTB+ Россия, украина, Кинодром и HD
CWS = 188.72.230.240 3002 6mfrlmc6 пароль 0102030405060708091011121314 # Триколор 36е
CWS_KEEPALIVE = YES
CWS_CONNECT_TIMEOUT = 200
CWS_INCOMING_PORT = 21000
#9
Отправлено 09 January 2013 - 21:34
Файл: \\192.168.0.101\Configuration\keys\replace.list - НЕ ЗАГРУЖЕН. (Ожидание смены канала ...)
ОШИБКА ЗАГРУЗКИ:
Файл: mg_cfg - не найден
Сетевое устройство ''192.168.0.101'' - вижу, но ...
Каталог ''\\192.168.0.101\Configuration\keys\'' - не найден или не доступен
---------------------------------------------------------------------------------------------------------------------------------------------------------------------
Инструкция: Задайте имя файла ''replace.list'' для загрузки, или
укажите каталог, IP-адрес или сетевое имя ресивера для поиска ...
---------------------------------------------------------------------------------------------------------------------------------------------------------------------
Последняя удачная загрузка: \\192.168.0.101\Configuration\keys\replace.list
Ожидание данных от MGCAMD ...
Если данные не поступают - откройте mg_cfg и задайте параметры:
C: { 01 }
L: { 01 } 192.168.0.102 514
... и перезапустите MGCAMD
#10
Отправлено 09 January 2013 - 21:34
#12
Отправлено 09 January 2013 - 21:40
#13
Отправлено 09 January 2013 - 21:44
#14
Отправлено 09 January 2013 - 21:44
192.168.0.102 это телевизор
нужно в параметре L вписать ip тюнера
4.8е, 13.е, 19е, 36.е, 75е, 0.8w, 4w, 5w
#15
Отправлено 09 January 2013 - 21:45
100 телевизор а 101 ресивер 102 телек
что то вы намудрили
4.8е, 13.е, 19е, 36.е, 75е, 0.8w, 4w, 5w
#16
Отправлено 09 January 2013 - 21:46
#17
Отправлено 09 January 2013 - 21:47
#18
Отправлено 09 January 2013 - 21:48
#19
Отправлено 09 January 2013 - 21:52
L: { 01 } 192.168.0.102 514
#20
Отправлено 09 January 2013 - 21:57
Количество пользователей, читающих эту тему: 0
0 пользователей, 0 гостей, 0 анонимных